Addastone Surface Protector is an advanced, heavy duty surface protection designed to treat and protect a variety of surfaces from liquids including oil, diesel, coffee and general water ingress, eliminating the harmful effects of moisture and possible staining. The treatment will also prevent frost damage.
• Non toxic
• UV Resistant
• Silicone free
• Environmentally friendly
• Transparent
• UV Resistant
• Silicone free
• Environmentally friendly
• Transparent
The Benefits are:
• Chewing Gum does not adhere
• Non flammable
• Protects against fungal growth
• Advanced water based technology
• Keeps surfaces looking natural
• Helps stop moss, lichen and algae forming
• Chewing Gum does not adhere
• Non flammable
• Protects against fungal growth
• Advanced water based technology
• Keeps surfaces looking natural
• Helps stop moss, lichen and algae forming
Cleaning of hands and tools: Clean all equipment with water after use.
Addagrip Surface Treatments UK Limited Addagrip House, Bell Lane Industrial Estate, Uckfield,East Sussex TN22 1QL, United Kingdom
Telephone: +44 (0)1825 761333 Fax: +44 (0)1825 768566
Addagrip Surface Treatments UK Ltd is a company registered in England
Registered No. 1492055 Vat No. GB 315993925
Telephone: +44 (0)1825 761333 Fax: +44 (0)1825 768566
Addagrip Surface Treatments UK Ltd is a company registered in England
Registered No. 1492055 Vat No. GB 315993925
Click here for our Surface protector brochure
One application will protect porous aggregates used in Addastone surfaces typically between 2 -10 years depending on usage.
Areas of use
Addastone resin bonded surfaces Stonework
Patios Block paving
Paving slabs Pedestrian areas
Car parks Garage floors
Addastone resin bonded surfaces Stonework
Patios Block paving
Paving slabs Pedestrian areas
Car parks Garage floors
Coverage
The coverage rate will vary depending on the profile and grade of the aggregate. Typical coverage rates are as follows: Natural Stone (medium porosity) 4-5m2/lt Concrete Slab 5.3m2/lt
The coverage rate will vary depending on the profile and grade of the aggregate. Typical coverage rates are as follows: Natural Stone (medium porosity) 4-5m2/lt Concrete Slab 5.3m2/lt
Surface preparation:
All surfaces must be free from dust, dirt, oil efflorescence, organic growth and any paints or protective coatings. Pressure washing up to 2500 psi for cleaning purposes is recommended, allow areas to dry. Addastone surfaces should have excess stone removed prior to application. If used to Protect new concrete allow a minimum of 28 days curing and drying before treatment. Optimum effectiveness of oil and water repellence is 7 days after treatment.
All surfaces must be free from dust, dirt, oil efflorescence, organic growth and any paints or protective coatings. Pressure washing up to 2500 psi for cleaning purposes is recommended, allow areas to dry. Addastone surfaces should have excess stone removed prior to application. If used to Protect new concrete allow a minimum of 28 days curing and drying before treatment. Optimum effectiveness of oil and water repellence is 7 days after treatment.
Application
Apply by brush, roller or low pressure spray. Addastone Resin Bonded surfacing must be back rolled to ensure all areas and peaks of aggregate are covered. Substrate Moisture – 5% maximum. Do not apply when rain or frost are expected. Apply one or two applications to achieve saturation of substrate. A second coat must be applied wet on “wet” within 10 minutes of previous application. Do not apply to excess. Addastone Surface Protector cannot be over coated with any other product as there will be a loss of adhesion.
Apply by brush, roller or low pressure spray. Addastone Resin Bonded surfacing must be back rolled to ensure all areas and peaks of aggregate are covered. Substrate Moisture – 5% maximum. Do not apply when rain or frost are expected. Apply one or two applications to achieve saturation of substrate. A second coat must be applied wet on “wet” within 10 minutes of previous application. Do not apply to excess. Addastone Surface Protector cannot be over coated with any other product as there will be a loss of adhesion.
Mixing Ready to use, no mixing required.
